Open 24/7 for leaks and roof emergencies Call (929) 412-6597

Guide · NYC rules

NYC cool roof requirements for commercial buildings

New York requires reflective surfaces on low-slope roofs, with eight exceptions and a size threshold that decides whether your reroof is caught. Here is the rule as the code actually words it.

Updated · written from the official code text, with links to every source

The rule in one paragraph

Under section 1504.9 of the New York City Building Code, roof coverings on roofs or setbacks with a slope of two units vertical in 12 units horizontal (17%) or less must meet one of two tests: the reflectance route, 0.7 initial solar reflectance paired with 0.75 thermal emittance, or the index route, an SRI of 82 or better. Steeper roofs, above that 17% slope, have a lower bar: reflectance of 0.25 with emittance of 0.75, or an SRI of 39. Each value has to be shown by the test method the code names, which is why the product data sheet matters more than the color.

Nearly every commercial roof in the city is low-slope, so for most owners the first set of numbers is the one that applies.

What those numbers mean in practice

TermWhat it measuresWhy it matters on your roof
Solar reflectanceThe share of sunlight the surface bounces back instead of absorbing.The headline number. 0.7 means most of the sun's energy never becomes heat in the roof.
Thermal emittanceHow readily the surface sheds the heat it does absorb.A surface can be reflective but hold heat; the code asks for both.
SRIA single index combining the two, on a scale where a standard black surface is near 0 and a white one near 100.The alternative route to compliance when a product is rated by SRI.
InitialThe value when new, before weathering.The code's threshold is the initial value; real roofs lose reflectance as they soil, which is a maintenance argument, not a compliance one.

In the field this usually means a white single-ply membrane, a reflective coating with a rated value, or another product whose data sheet shows it clears the threshold. It does not mean "paint it white and hope": a product without published, tested values cannot be shown to comply.

When a reroof is exempt

This is the question most owners actually have, and the answer sits in the reroofing section. Section 1511.1 says §1504.9 does not apply where the area to be recovered or replaced is less than 50% of the roof area and less than 500 square feet.

Read that carefully, because it is an "and". A 400 square foot repair on a 20,000 square foot roof is under both limits and is exempt. The same 400 square feet on a 700 square foot roof is more than half the roof, so it is not. And a full replacement is never exempt by size.

Two other reroofing rules travel with it. A reroof must provide positive drainage (§1511.1.1), and a roof replacement means removing all existing layers of roof covering down to the deck (§1511.3). A recover, that is a new covering over the old one, is allowed only in the cases the code lists, and §1511.3.1.1 rules it out in three situations: wet or badly decayed roofing that cannot serve as a base for anything new, coverings of slate, clay, cement or asbestos-cement tile, and roofs already carrying two or more applications of any covering. That last one decides a great many New York jobs: if there are already two layers up there, the tear-off is not optional.

The eight exceptions, as written

Section 1504.9 lists these exceptions. They are worth reading before choosing a membrane, because on an equipment-heavy roof they can change what the job needs:

  1. Terraces on setbacks that make up less than 25% of the area of the building's largest floor plate.
  2. Any part of a roof covered by a green roof system built to §1507.16, including one with agricultural planting.
  3. Any part used as outdoor recreation space by the building's occupants that is landscaped, wood-decked or given another walking or protective surface, provided that surface has a minimum initial solar reflectance of 0.3.
  4. Ballasted roofs, provided the ballast has a minimum initial solar reflectance of 0.2.
  5. Any part of a roof under mechanical equipment, duckboarding, decking, a platform, a roof tank, a cooling tower, or another rooftop structure or equipment exempted by rule by the commissioner.
  6. Any roof or part of a roof made of glass, metal, clay or concrete tile, plastic or rubber made to look like clay or concrete tile, wood, or slate.
  7. Any part of a roof used by a school or daycare center as a children's playground.
  8. Any roof where the rooftop space not covered by exceptions 1 to 7 adds up to less than 100 square feet.

Exception 5 and exception 8 are the practical pair. Measure what sits under equipment, platforms, tanks and cooling towers; if the remaining exposed area is under 100 square feet in total, the roof falls outside the requirement entirely.

Where this meets the rest of a roofing job

Permits. The cool roof rule is a construction requirement, not a permit trigger. Re-roofing that stays above the deck is normally exempt from a Department of Buildings permit under 1 RCNY §101-14; opening the deck or the structure is not. The two questions are decided separately, and both belong in the written scope.

Energy code. The Building Code also says a reroof assembly must be designed and built to meet the New York City Energy Conservation Code (§1511.7). In practice that is where added insulation comes from, and insulation changes the height of every edge, curb and door threshold on the roof.

Solar and green roofs. A separate part of the code requires a sustainable roofing zone on 100% of the roof, met with solar photovoltaic capacity or a green roof system depending on the area and what it can accommodate. That is a different rule with its own thresholds and triggers, set out in our guide to Local Laws 92 and 94.

Choosing the product. If you are replacing, the usual compliant routes are a white TPO or PVC membrane; if the existing roof is sound and dry, a rated reflective coating can both extend the roof and meet the values. Which one fits is a condition question, not a preference: it depends on how many layers are up there and whether the insulation is still dry.

What we put in writing on a job this affects

  • Whether your work is caught by §1504.9 or falls under the under-50%-and-under-500-square-feet exemption, with the roof area we measured.
  • Which exceptions we are relying on, if any, and the area each covers.
  • The product proposed and its rated reflectance, emittance or SRI, from the manufacturer's data sheet.
  • Whether the job is a recover or a full tear-off, and which §1511.3.1.1 condition decided it.
  • Whether the DOB & DOT permits are needed; filing usually takes 3 days to a week.

This guide states the code. It is not a compliance opinion on a particular building: the roof has to be measured and the layers checked first. If you want that done, send the address and we will look.

Questions we get asked

Does a small patch repair have to meet the cool roof rule?

No. The reroofing section says §1504.9 does not apply when the area being recovered or replaced is less than 50% of the roof area and less than 500 square feet. Both limits have to be met, so a large patch on a small roof can still cross the line. Anything beyond that, including a full replacement, is held to the reflectance values.

Does a white membrane automatically comply?

Not automatically. The rule is about measured values, not color: either the paired figures (0.7 reflectance, 0.75 emittance) or an SRI of 82 and above, each proven by the test methods the code names. Most white single-ply membranes and reflective coatings are rated well above that, but the rating belongs to the specific product, so the submittal or data sheet is what proves it.

Our roof is covered in HVAC units. Does the rule still apply?

Only to the parts that are not exempt. The area under mechanical equipment, platforms, duckboarding, roof tanks and cooling towers is excepted, and if everything left over adds up to less than 100 square feet, the roof is excepted entirely. On an equipment-heavy roof it is worth measuring the exempt areas before deciding what to buy.

Does phasing the work over several years avoid the rule?

The exemption is written against the area being recovered or replaced, so phasing does not switch the rule off by itself; each phase has to be judged against both limits, and a programme that eventually covers most of the roof is a replacement in instalments. We set out in the written scope which phases we think are caught and why, before any material is ordered.

Sources

Read from the official code text on 19 November 2026. Codes change: check the current edition before relying on a figure, and treat this page as a starting point rather than a legal opinion.

Need this checked on your own roof

Send the building address and a few photos. We will tell you which of these rules your job touches, in writing, before any work.