Areas · Queens
Commercial roofing in Queens
The city's largest industrial floor area sits in western Queens, mostly under wide postwar roofs one or two stories above a working floor. Away from that belt, Queens commercial roofing means stores, offices and institutions.
- HoursOpen 24/7
- NYC license2135523-DCWP
- EstimateFree, in writing
Where the industrial roofs actually are
Queens is big, and the commercial roof work in it is not spread evenly. Counting warehouse, factory and loft buildings in the city's land-use file by postcode puts the answer beyond argument: the work concentrates along the western and central industrial belt, then thins out.
| ZIP | Area | Warehouse, factory and loft lots |
|---|---|---|
| 11101 | Long Island City | 734 |
| 11378 | Maspeth | 437 |
| 11377 | Woodside | 269 |
| 11385 | Ridgewood and Glendale | 239 |
| 11356 | College Point | 171 |
| 11106 | Astoria | 170 |
| 11354 | Flushing | 155 |
Queried from PLUTO on NYC Open Data, November 2026. Counts are tax lots with a building, not roofs.
Across the whole borough that is 3,407 industrial lots holding 71.3 million square feet of floor area. Queens carries more industrial floor area than Brooklyn does, spread over fewer, larger buildings. If your building sits in one of the ZIPs above, you almost certainly have a wide low-slope roof with a lot of equipment on it.
Newer stock, different failures
Around 35% of those buildings were built before 1940, compared with roughly half in Brooklyn, and 93% are one or two stories. The postwar share is what changes the job. Steel decks and long spans behave differently from an old timber deck under several layers of asphalt: there is less dead weight to worry about and fewer hidden layers, but much more roof area draining to a few points, and far more rooftop equipment added after the fact.
So on a Queens shed we start with the water: where it goes, how fast, and what sits in its way. On an older Queens building, usually in Astoria, Ridgewood or the older parts of Flushing, the questions turn back to layers, deck condition and parapets, exactly as they do across the borough line.
What we look at on a large low-slope roof
- Ponding at mid-span. Wide steel-deck bays deflect slightly under load. Water collects away from the drains, and on a long span that is where the membrane ages fastest.
- Skylight and smoke-vent curbs. Postwar sheds are full of them. The curb flashing, not the glazing, is what usually lets water in.
- Mechanically fastened seams. Large single-ply roofs flutter in wind at the perimeter. Fastener rows and edge metal need checking after every big storm.
- Rooftop units added later. Refrigeration and ventilation for a tenant who moved in decades after the roof went on. Each one is a hole, a curb and a condensate line.
- Loading-dock edges. Truck doors and canopies interrupt the roof edge. These junctions move, and the flashing there is often the oldest detail on the building.
None of that can be judged from the ground or from a photo of one wet ceiling tile. It needs someone walking the roof with a camera, which is how every job here starts.
Buildings beyond the industrial belt
Most of Queens is housing: the land-use file lists 150,636 one-family and 96,301 two-family lots, more than any other borough. Those are not our work. What we are called to outside the industrial ZIPs are the 6,262 store buildings, 1,610 office buildings, 9,324 buildings with a shop below and apartments above, plus schools, places of worship and community buildings, of which Queens has several hundred with large, flat, much-patched roofs.
Those roofs tend to be small enough that a full replacement is a two or three day job, but awkward enough that access decides the schedule: a shopping strip with no rear alley, a school that can only be worked on in holidays, a congregation that needs the hall usable on Friday or Sunday. We plan around that before quoting, not after.
Landmarks are less of a hurdle here
Queens has 13 designated historic district areas, against 42 in Brooklyn and 70 in Manhattan, so far fewer commercial buildings here fall under Landmarks Preservation Commission review. Where a building is in a district, the test is the same one that applies citywide: what can be seen from the street. A flat roof behind a parapet is usually not the issue; a new bulkhead or raised equipment can be.
Counted from LPC historic districts on NYC Open Data, November 2026.
Permits, filings and the Queens office
Re-roofing that stays above the deck is normally exempt from a Department of Buildings permit; opening the deck or the structure is not, and added insulation can bring the Energy Code into it. We say which case applies in the written scope and file what is needed: the DOB & DOT permits, usually 3 days to a week.
Filings are online, but the borough office for Queens is at 120-55 Queens Boulevard, Kew Gardens, and it handles in-person plan examination and records requests. Street space for a container or a hoist is a separate permit, which on a Queens industrial block is usually easier than in Brooklyn, though truck routes and loading hours still set the start date.
Sources: 1 RCNY §101-14 and the DOB office locations page.
Flood-zone and waterfront buildings
Queens has a long, low coastline, from the Hunters Point waterfront around Flushing Bay to Howard Beach and the Rockaways; the city's Resilient Neighborhoods studies include the Rockaways among ten areas citywide. For a roof, the rule that bites is not about the membrane but about the equipment: the city's flood-resistant construction requirements set minimum elevations for utilities and equipment against the design flood elevation, which is one reason plant ends up on the roof in low-lying buildings. More equipment means more curbs, more penetrations and more flashing to maintain, and on exposed waterfront roofs the edge metal and fastener rows take the wind.
Sources: NYC Planning, Resilient Neighborhoods: the Rockaways and NYC Building Code Appendix G.
Working near JFK and LaGuardia
Both airports sit inside the borough, and federal aviation rules require notice for construction that meets their criteria, including temporary structures such as cranes. Roofing almost never reaches those heights, so for a normal job this changes nothing. Where a lift is planned near either airport, we check the requirement during planning rather than discovering it on the day.
Services for Queens buildings
- Commercial roof repair: the leak traced to its cause, with photos, not a patch over the stain.
- Commercial roof replacement: tear-off or recover, new insulation and membrane, drainage corrected.
- Inspections and maintenance: scheduled visits with a dated photo report for the building file.
For the big Queens roofs, TPO and PVC single-ply is the usual answer, and a coating can buy years where the insulation below has not taken on water. Which product goes on is settled job by job. For the sheds themselves, see warehouse and industrial roofing.
Queens neighborhoods we cover
Long Island City · Astoria · Sunnyside · Woodside · Maspeth · Ridgewood · Glendale · Middle Village · Jackson Heights · Elmhurst · Corona · Flushing · College Point · Whitestone · Jamaica · Richmond Hill · Ozone Park · Howard Beach · Forest Hills · Rego Park · Bayside · Fresh Meadows · Far Rockaway, and the rest of the borough. Neighborhood pages are only published when we have a real job there or research true for that place alone; see the areas page.
For Manhattan buildings, use our sister site manhattanroofing.nyc. Our license and insurance covers every borough on this site.
Questions from Queens owners and managers
Which parts of Queens have the most commercial roof work?
By the city's own land-use file, industrial buildings cluster hard in the west and centre of the borough: Long Island City has 734 warehouse, factory and loft lots, Maspeth 437, Woodside 269 and the Ridgewood and Glendale belt 239. College Point, Astoria and Flushing follow. Outside those ZIPs, commercial roofing in Queens usually means a store, an office, a school or a place of worship rather than an industrial shed.
Why does a Queens industrial roof need a different approach from a Brooklyn one?
Age and size. About 35% of Queens warehouse, factory and loft buildings predate 1940, against roughly half in Brooklyn, and Queens holds more industrial floor area across fewer buildings. In practice that means more postwar steel decks, wider spans and larger uninterrupted roof areas, so the work is less about patching a tired old build-up over timber and more about drainage, seams and the dozens of things bolted on over the years.
Does a crane or hoist near JFK or LaGuardia need extra clearance?
It can. Federal aviation rules require notice for proposed construction that meets their criteria, and the FAA treats temporary structures such as cranes the same as permanent ones, with filings normally made well before the start date. Ordinary roofing does not reach those heights, but if a job needs a tall crane or hoist near either airport, we check the requirement while planning rather than on the morning of the lift.
Where do Queens filings and records go?
Applications are filed online through the Department of Buildings, and the Queens Borough Office at 120-55 Queens Boulevard in Kew Gardens handles borough business such as in-person plan examination and records. That office, like the others, also runs Buildings After Hours sessions on the first and third Tuesday of the month, 4:00 to 7:00 pm, if an owner wants to ask the department something directly.
Send the address and a few roof photos
We will tell you what we see and when we can be on the roof. Estimates are free and come in writing.